Engineering Plastics | Busy Bee Brushware

Nylon Rod

Not sure which option is best for you? Please Contact Us and our friendly team will be happy to help.

DISCLAIMER: It’s always the clients decision to ensure that the materials are right for the specification.

The post UHMWPE Engineering Plastic Rod first appeared on Busy Bee Brushware.

Truck Mud Flaps BLACK Set of 2 – Heavy Duty

Andrea Frier — Sun, 11 Feb 2024 04:49:08 +0000

HEAVY DUTY TRUCK MUD FLAPS – BLACK – SET OF 2

Suitable for your large or heavy duty applications. Not rubber or PVC, these are made from HDPE High Density Polyethylene. So they are made for your bigger trucks, large earth movers and mining vehicles, road maintenance equipment.

HDPE mud flaps provide great protection against road debris, reducing the risk of damage to your vehicle’s undercarriage and enhancing safety. It helps to prevent mud, water and other debris kicking up onto the vehicle or trailer, or underneath.

High-Density Polyethylene (HDPE) is an excellent material choice for your truck mud flaps due to its durability, flexibility, and resistance to corrosion, chemicals, and UV radiation. Made to last. They are lightweight, which contributes to fuel efficiency of your vehicle. As well as making installation easier. No specialised equipment is required for fitting. Install your own bolt holes as required. Comes with small 5mm radius on each corner.

The surface inhibits mud and other debris from building up. You will find these much easier to wash than your standard rubber or other plastic mud flaps. Mud literally slides off.

Additionally, HDPE is recyclable, making it your environmentally friendly option.

Available Sizes – SET OF 2

24″/605mm Width

24″/605mm
30″/760mm
36″/910mm

29″/740mm WIDTH

29″/740mm
36″/910mm
39″/990mm

39″/990mm

24″/605mm
29″/740mm
36″/910mm

Custom Sizes available: please contact us with your measurements. Or you can choose one size larger than needed, but when you go to our Shopping Cart/Checkout let us know in your purchase comments the size that you would like to have cut.

Packaging: We flat pack your Truck Mud Flaps in heavy duty cardboard to protect it during transit. Your Truck Mud Flaps may also have a protective film which you peel off prior to installation. If you have trouble removing the film, try sticking some tape near the edge to lift the film and peel off.

Shipping:

For sizes 1000mm and over, please supply a location address and phone number in your comments. Australia Post shipping not available for sizes over 1000mm, flat rate courier shipping only.

Check out our Truck Whiskers here.

Not sure which option is best for you? Please Contact Us and our friendly team will be happy to help.

The post Truck Mud Flaps BLACK Set of 2 – Heavy Duty first appeared on Busy Bee Brushware.

Workstation Magnet Mate – Industrial Pen Holder

Andrea Frier — Fri, 28 Jul 2023 00:52:53 +0000

Keep your pens handy with our industrial strength Workstation Magnetic Pen Holder.

Your best mate in the factory, workshop, warehouse, on the forklift or any worksite.

What is a Workstation Magnetic Pen Holder?

Made from 3D printed PLA Polyester, so is strong and hard wearing. Fitted with an industrial strength Pot Magnet N38 ASNQ-A42. Designed with 2 holes, one for a standard pen, the other for a Permanent Marker. Keeps your pens close and ready to use at any time.

How to use your Workstation Magnetic Pen Holder:

Designed for the workshop, factory, construction or worksite or warehouse
Attach to cabinets, pallet racks, machinery, stairs, forklifts, utes, anything magnetic!
Portable – can be relocated as needed without dismantling
Strong – not easy to knock over, holds well to any steel surface
Encourages return of the pens to their Holders, less likely to disappear in pockets!
One for each workstation in line with LEAN Principles, the right tool exactly where you need it
Coloured for easy identification

What colours does the Workstation Magnetic Pen Holder come in?

Red, Blue, Yellow, Green

Purchase as Singles, 3-pack, 6-pack, 12-pack

Purchase as a 4 colour pack in pack of 4, and pack of 12 (3 of each colour)

Options:

Pen Holder including Magnet – you supply your own pens
Complete with Artline 70 Permanent Marker Black and our own Busy Bee stylus Pen

How can I purchase?

Buy as Singles, or in quantities of 3 units, 6 units, 12 units. Or purchase in packs of 4 with one of each colour in multiple packs of single (4 pen holders), or 3-pack (12 pen holders).

Why choose BB Engineering Plastics as your Plastic Supplier?

Not sure which option is best for you? Please Contact Us and our friendly team will be happy to help.

The post Workstation Magnet Mate – Industrial Pen Holder first appeared on Busy Bee Brushware.

HDPE Engineering Plastic Rod

Dearna Edwards — Mon, 28 Nov 2022 23:52:13 +0000

What is HDPE?

HDPE stands for High-Density Polyethylene. It is a type of plastic which is a thermoplastic polymer made from petroleum. HDPE is known for its high strength-to-density ratio and is used in a variety of engineering and industrial applications.

What are the properties of HDPE?

Durability: HDPE is a durable and tough plastic, making it suitable for applications where strength and resilience are essential.
Chemical Resistance: HDPE is resistant to many chemicals, making it suitable for use in containers and pipes for transporting a wide range of substances.
Weather Resistance: It has good resistance to UV rays and is not prone to environmental stress cracking, making it suitable for outdoor applications.
Versatility: HDPE is a versatile material used in various industries, including packaging, construction, automotive, and agriculture. Common products made from HDPE include bottles, pipes, toys, containers, and more. It is also easy to machine and fabricate.
Recyclability: HDPE is recyclable, and recycled HDPE is used in the production of new products.
Low Moisture Absorption: HDPE has low moisture absorption, making it suitable for applications where moisture resistance is important.
Lightweight: Despite its strength, HDPE is relatively lightweight, making it easy to handle and transport.

Can HDPE handle heat?

HDPE typically has a melting point in the range of 120 to 130 degrees Celsius (248 to 266 degrees Fahrenheit). While it can handle temperatures well within the range of typical outdoor and industrial applications, it may not be suitable for extremely high-temperature environments.

For applications requiring resistance to higher temperatures, other engineering plastics with higher heat resistance, such as polypropylene, polyethylene terephthalate (PET), or polyetheretherketone (PEEK), might be more suitable.

Is HDPE Plastic suitable for Food Grade applications?

Yes, HDPE (High-Density Polyethylene) is commonly used in food-grade applications. HDPE is considered a food-safe material because it is inert, meaning it does not react with or leach chemicals into food or beverages. It has several characteristics that make it suitable for food contact:

Inertness: HDPE is chemically inert, which means it does not react with the substances it comes into contact with. This property ensures that there is minimal risk of the material contaminating the food or altering its taste.
Non-Toxic: HDPE is a non-toxic material, and it is generally approved by regulatory agencies for use in food packaging and storage.
Resistance to Chemicals: HDPE is resistant to many chemicals, which is an important feature for materials that will be in contact with food items.
Easy to Clean: HDPE surfaces are smooth and easy to clean, making it suitable for applications where hygiene is crucial, such as food packaging and storage containers.
Durability and Strength: HDPE is a durable material that can withstand the rigors of food handling and transportation.

Common food-grade applications of HDPE include food containers, bottles, cutting boards, food storage bins, and other packaging materials.

How strong is HDPE?

High-Density Polyethylene (HDPE) is known for its high strength-to-density ratio, making it a strong and durable material. The strength of HDPE can be influenced by various factors, including the specific grade of HDPE, the manufacturing process, and the intended application. Here are some general characteristics related to the strength of HDPE:

Tensile Strength: HDPE has a high tensile strength, which means it can withstand pulling forces without breaking. The tensile strength of HDPE typically ranges from 20 to 37 MPa (megapascals), depending on the grade.
Flexural Strength: HDPE also exhibits good flexural strength, allowing it to resist bending without permanent deformation. The flexural strength can vary but is generally in the range of 12 to 33 MPa.
Impact Strength: HDPE is known for its excellent impact resistance. It can absorb and distribute impact energy, making it suitable for applications where impact resistance is crucial.
Compressive Strength: HDPE has a high compressive strength, allowing it to withstand loads applied in a perpendicular direction. The compressive strength of HDPE can vary but is typically in the range of 15 to 40 MPa.
Fatigue Resistance: HDPE exhibits good fatigue resistance, making it suitable for applications involving repeated stress or strain.

It’s important to note that the specific mechanical properties of HDPE can vary depending on the grade, processing conditions, and any additives incorporated during manufacturing. Engineers and designers often choose a HDPE grade based on the requirements of the specific application, taking into consideration factors such as load-bearing capacity, environmental conditions, and regulatory compliance.

Uses of HDPE Rod:

Machined Parts and Components
Packers, rollers, lifting blocks
Bushings and Bearings
Seals and gaskets
Pump components
Pipes and fittings
Electrical insulation
Medical and food manufacturing applications

What colour is HDPE Engineering Rod?

HDPE Rod is available in Natural (White) and Black

Environmental and end of life considerations

HDPE is a highly recyclable plastic. The recycling process for HDPE involves melting and reforming the material, and recycled HDPE can be used to manufacture a variety of products, including new HDPE items.

Why choose BB Engineering Plastics as your Plastic Rod Supplier?

Check out our other Plastic options online:

Nylon Rod

Not sure which option is best for you? Please Contact Us and our friendly team will be happy to help.

DISCLAIMER: It’s always the clients decision to ensure that the materials are right for the specification.

The post HDPE Engineering Plastic Rod first appeared on Busy Bee Brushware.

Nylon Engineering Plastic Rod

Dearna Edwards — Tue, 18 Oct 2022 21:19:25 +0000

What is Nylon?

Nylon engineering rod is a versatile and durable cylindrical material made from nylon plastic, renowned for its exceptional toughness, impact resistance, and suitability for many industrial applications. Also known as Ertalon, Polyamide, Nylatron, Tecast T, Zytel, Techtron

What are the properties of Nylon?

High toughness and impact resistance.
Excellent wear and abrasion resistance.
Good chemical resistance to oils, greases, and some solvents.
Low friction coefficient, making it suitable for bearing and sliding applications.
High strength and stiffness, especially in comparison to other plastics.
Relatively low moisture absorption, leading to dimensional stability.
Good electrical insulating properties.
Resistant to many common chemicals and alkalis.
Can withstand a wide range of temperatures, typically from -40°C to around 120°C (-40°F to 248°F) depending on the specific grade.
Versatile processing capabilities including machining, injection molding, and extrusion.
Available in various colors and formulations for specific applications.

Keep in mind that the specific properties can vary depending on the grade and manufacturer of the nylon material.

Is Nylon Plastic Rod Food Grade?

Nylon materials that are often considered food grade include Nylon 6 and Nylon 6/6.

How strong is Nylon?

Nylon engineering rods are known for their remarkable strength, typically boasting tensile strengths in the range of 10,000 to 15,000 psi (69 to 103 MPa). This impressive strength is particularly notable considering nylon’s relatively lightweight nature. It enables the material to withstand significant mechanical loads, making it suitable for a wide array of applications, such as gears, bearings, machine components, and structural parts. The specific strength can vary depending on the grade and formulation of the nylon, and it’s crucial to select the appropriate grade to match the demands of the intended application for optimal performance and longevity.

How does Nylon wear?

Nylon engineering rods are highly hard-wearing due to their exceptional abrasion resistance and durability, making them suitable for applications involving repeated friction, wear, and impact.

Can Nylon handle water and outdoor conditions?

Yes, nylon engineering rods generally have good water resistance and can withstand outdoor conditions well due to their low moisture absorption, durability, and resistance to UV degradation, making them suitable for outdoor applications.

Uses of Nylon:

Gears and sprockets in machinery.
Bearings and bushings.
Wear-resistant components.
Conveyor system parts.
Rollers and wheels.
Electrical insulators.
Automotive components.
Structural supports.
Fasteners and threaded components.
Food processing equipment parts.
Medical equipment components.
Marine hardware.
Sports equipment components.

Nylon engineering rods are chosen for these applications due to their strength, toughness, wear resistance, and versatility.

What colour is Nylon Engineering Rod?

It is a “Natural” colour which is cream/opaque, and can also be sourced in Black.

Environmental and end of life considerations

Nylon engineering rods can have a relatively long service life and can be recycled, contributing to environmental sustainability, but their end-of-life disposal may still involve challenges due to limited recycling infrastructure for certain grades.

Why choose BB Engineering Plastics as your Plastic Rod Supplier?

Check out our other Plastic options online:

Not sure which option is best for you? Please Contact Us and our friendly team will be happy to help.

DISCLAIMER: It’s always the clients decision to ensure that the materials are right for the specification.

The post Nylon Engineering Plastic Rod first appeared on Busy Bee Brushware.

PEEK Engineering Plastic Rod

Andrea Frier — Wed, 12 Oct 2022 01:58:49 +0000

What is PEEK?

PEEK stands for PolyEther Ether Ketone. PEEK is a colourless high-performance semi-crystalline engineering thermoplastic. Also known as Ketron, LNP, KetaSpire, Sustapeek, Tecapeek.

What are the properties of PEEK?

Superior strength-to-weight ratio.
Creep-resistant.
Abrasion resistant.
Long-wearing, low wear and tear.
Withstands very high temperatures.
Radiation- and chemical-resistant.
Low water absorption.
Easy to machine and fabricate.

Is PEEK Plastic Rod Food Grade?

PEEK has FDA approval. This means it is safe for direct contact with delicate foods during the production process. For this reason, PEEK food handling components are used in both food packaging and food production processes.

How strong is PEEK?

Compared to metals such as aluminium and steel, PEEK has greater tensile strength. Furthermore, it can withstand prolonged exposure to high temperatures, harsh chemicals, and moisture. PEEK is a strong material with a GPa of 3.6 and a tensile strength of 90 to 100 MPa.

So it makes sense for engineers to consider PEEK material. What’s more it is easily machinable and long lasting to replace heavier metal parts. Furthermore, with PEEK being a lighter material than metal parts, it can contribute to lower energy consumption.

How does PEEK wear?

PEEK machining rod has a great wearing capability, including adhesive, abrasive, corrosive, and surface-fatigue wear. Therefore, it makes sense to consider PEEK when you next need to replace bearings or seals as part of your regular machinery maintenance. And then having that kind of reliability and safety means your improvement in productivity can be well worth the expense.

Can PEEK handle water and outdoor conditions?

With very low water absorption properties, PEEK is ideal for water applications even in high humidity. Also, it is resistant to salt water and steam. (Note, however, PEEK is sensitive to UV Radiation which can cause the polymer to become brittle). For applications that require high resistance to chemicals or voltage, PTFE Teflon Rod may also be suitable.

Uses of PEEK:

Bushings
Bearings
Seals
Back-up rings
Pump and valve components
Vacuum wand handles
Semiconductor machinery components
Electrical connectors
Medical and food manufacturing applications

What colour is PEEK Engineering Rod?

It is a “Natural” colour which is light brown/beige.

Environmental and end of life considerations

With PEEK being a thermoplastic, it has a very high melting temperature and combustion temperature is in excess of 600c. Moreover, when exposed to flames, this engineering plastic rod emits little smoke or toxic gas fumes. So is relatively safe to the environment. PEEK can be broken down, reprocessed and recycled.

Why choose BB Engineering Plastics as your Plastic Rod Supplier?

Check out our other Plastic options online: