MARINE BOATBOARD – SPECIAL ORDER ITEM

Please contact us for availability of remaining stock thicknesses, or we can arrange special order.

12.7mm (1/2 inch)

19mm (3/4 inch)

25.4mm (1 inch)

Weather-Resistant Sheet for Marine and Outdoor Living Products

BoatBoard, also known as Marine Board and Starboard,  is a special grade plastic High Density Polypropylene (HDPE) which is UV-stabilized and has a textured surface on both sides.  Given its combination of long term performance, durability, appearance, fabrication ease and consistency, it is a product of choice for boat builders around the world. In boat building components, this tough, UV resistant sheet withstands long exposure to intense sun, salt water and rigorous outdoor use.

HDPE Boatboard is also known as:

• HDPE boatboard
• Marine board
• Kingstar board
• Sea board
• PE100 boat board
• PE100 UV
• Bait board

HDPE Boat Board Applications

• Marine applications
• Boat Instrument panels
• Deck & seating components
• Doors
• Hatch & well covers
• Tables
• Trim
• Outdoor cabinets
• Storage & tackle bins
• Cup & rod holders
• Steps & grab rails

PLESE NOTE – For full sheet purchase, freight will need to be quoted on Order.  Or we can cut into 4 panels for most economical shipping method.

Australia Post Shipping Is NOT available for lengths above 1m,flat rate courier shipping only.

Please supply a physical address and contact number as our couriers cannot deliver to a PO Box, plus any special instructions for our Courier, eg. leave at side door if not at home. Thank you.

Boat Trailer Accessories – Outboard Motor Wedges – Set of 2 – OBSOLETE ONCE SOLD

5 Degree Motor Wedges Suits Most Standard Footprints for Motors 40Hp to 90Hp.

• High quality Polyurethane (PE) (Black)
• Adds 5 degrees of tuck (negative tilt) to engine, so the motor sits lower in the water
• Improves performance for boats with insufficient transom angle
• Improves boat planing at low speeds
• Fits All Standard Outboard 4-Bolt Patterns
• Full Contact Between Outboard Engine Bracket and Boat Transom

Additional Information:

The offset from top to bottom hole is approx. 40mm and distance between top and bottom hole is approx. 200mm.

Tapers from approx. 25mm thick one end to approx. 4mm.

Check out our other boating products.

Limited Stock Remaining, please Contact Us for stock availability.

Boat Trailer Accessories – Polyurethane V Block

Come In a Variety Of Sizes:

• 2 Inch- Base Width=50mm, Fork Width=85mm, Depth Of V=40mm, 1/2″ Pin Hole – Out of Stock
• 3 Inch- Base Width=75mm, Fork Width=105mm, Depth Of V=50mm, 1/2″ Pin Hole – Out of Stock
• 4 Inch- Base Width=90mm, Fork Width=110mm, Depth Of V=50mm, 1/2″ Pin Hole – 1 remaining
• 5 Inch- Base Width=110mm, Fork Width=135mm, Depth Of V=80mm, 1/2″ Pin Hole – Out of Stock
• 6 Inch- Base Width=110mm, Fork Width=150mm, Depth Of V=45mm, 1/2″ Pin Hole – 1 remaining

Special Order item, Made in Australia

For use with fibre glass boats due to the soft compound Polyurethane.

Available In:

• 7″ dia (105mm) -3/4″ Pin – (1 REMAINING)
• 8″dia (120mm) -4/8″ Pin – (3 REMAINING)

Limited Stock Remaining, please Contact Us for stock availability.

For use with fibre glass boats due to the soft compound Polyurethane.  Not all sizes are stocked but are available as a Special Order.

Available In:

• 4.5″ dia – to suit 5/8″ Pin Size – OUT OF STOCK
• 6″ dia – to suit 5/8″ Pin Size  – 3 LEFT IN STOCK
• 8″ dia – to suit 5/8″ Pin Size – OUT OF STOCK
• 9″ dia – 5/8″ Pin Size  – OUT OF STOCK
• 10″ dia – 5/8″ Pin Size – 3 LEFT IN STOCK
• 12″ dia – 1″ Pin Size – OUT OF STOCK

Used for boat trailers

Limited Stock Remaining, please Contact Us for stock availability.

For use with fibre glass boats due to the soft compound Polyurethane

Available In:

• 4″- 5/8″ Pin Size – (38 REMAINING)
• 6″- 5/8″ Pin Size – SOLD OUT
• 8″- 5/8″ Pin Size – (4 REMAINING)
• 12″- 1″ Pin Size – (7 REMAINING)

Limited Stock Remaining, please Contact Us for stock availability.

For use with fibre glass boats due to the soft compound Polyurethane

Available In:

• 4″ dia – 5/8″ Pin Size – DISCONTINUED
• 4.5″ dia – 5/8″ Pin Size – DISCONTINUED
• 6″ dia – 5/8″ Pin Size – 1 LEFT IN STOCK
• 8″ dia – 5/8″ Pin Size – 8 LEFT IN STOCK
• 12″ dia – 5/8″” Pin Size  – DISCONTINUED

Limited stock remaining

For use with fibre glass boats due to the soft compound Polyurethane

#customTable#